Nightcore Daycore
About
- Username
- Nightcore Daycore
- Joined
- Visits
- 3,808
- Last Active
- Roles
- Member
Comments
-
Will you also please change the highest frequency band from 16KHz to 15KHz? Because, what if older generations are also using the app as well? Because as you get older, you're not gonna hear higher frequencies as much when it comes to the 15KHz-17KH…
-
Sometimes, 150% may not always be enough in Track Isolation Splitter.
-
Will you please also extend the percentage of Track Isolation Splitter from 150% to like 200% or more when it comes to super low parts in a song headroom wise and dynamic range wise? Because, turning the drums or vocals down in some songs almost sou…
-
And, will you please also add 20 Hz to the equalizer as the update? It's the lowest frequency of human hearing. It's the starting point of it.
-
Single Minded Productions, LLC, has that ever happened to you? Where you added your favorite track to Track Isolation Splitter and the ending point of the song cuts off unexpectedly/out of nowhere/out of the blue? Did it made you delete it from Comp…
-
I could be right or wrong about it/this.
-
I realized that it's Track Isolation Splitter itself that's doing the ending point errors that cuts off in tracks/songs and not the tracks that I downloaded from a music downloading app. No idea what's causing it to happen, to be honest.
-
Which is also known as the Brilliance and Sheen range in that section
-
I also forgot to put "shimmery" in the 8KHz & 16KHz frequency range section
-
This also means that you're not allowed to fix the Track Isolation Splitter errors that cuts off in some song's/track's ending points?
-
Or, is it both?
-
@Iqmal Hakimi That could be a good idea
-
@"Iqmal Hakimi" Same, I hope so. Some tracks in Track Isolation Splitter tends to cut off only at ending points of a song and it annoys me a little bit.
-
Totally, it should happen.
-
That's actually a great idea
-
I'll explain it again for my official explanation: Some tracks do tend to cut off in Track Isolation Splitter itself in ending points only even though the split tracks are complete. I have no idea what caused it to happen on some tracks with cut-off…
-
I'm now assuming that the 20 Hz is in Upgrade to Pro?
-
And by "fixed", I'm talking updated.
-
Is it possible to fix Track Isolation Splitter? Or no?
-
Especially when it comes to the Music Speed Changer settings
-
Or, is there nothing that can be done about it?
-
It does the same thing on my Phillips TV. The Balance number range and Equalizer dB range are both at -10 minimum and +10 maximum.
-
Okay, thank you. It's making sense now.
-
Is there anything else I can do to fix Track Isolation Splitter to remove the cutting end points to some tracks/songs?
-
Are you 100% sure that it's the rate itself and not the loop timing improvement and marker button presses that makes the audio distort? If yes, that makes 100% sense now.
-
Unfortunately, yes it did. I left/reset the preamp to default 0 dB, and the ending point that cuts off in some of the songs in Track Isolation Splitter did the same exact thing.
-
Is the ceiling the input gain of the Limiter and the Threshold is the output gain of the Limiter? Or, no? Am I off about this?
-
I tried turning up the input gain 1 dB and more as I lower the threshold a couple dB down and more, and it's actually the right, correct, better and proper way to compress in general. Because the maximum input gain is up to 24 dB, it makes the thres…
-
Now, the equalizer bands will be updated to 9.
-
Yes, thank you so much. I'm going to be so excited for it the update when it happens.
Howdy, Stranger!
It looks like you're new here. If you want to get involved, click one of these buttons!